4.25. Altera SoCFPGA

Alteras SoCFPGA SoCs have a two-stage boot process. The first stage is known as preloader which loads the second stage bootloader. barebox can act as both the first and the second stage loader. In barebox the preloader is called xload, so to build as a first stage loader, build the socfpga-xload_defconfig; for second stage use the normal socfpga_defconfig.

4.25.1. Bootstrapping

The supported bootsources are: SD card and QSPI.

4.25.1.1. Bootsource selection

Board BSEL[2:0] CSEL[1:0]
Sockit SD 0b100 0b00
Sockit QSPI 0b110 0b00
Socrates SD 0b101 0b11
Socrates QSPI 0b111 0b11
SocDK SD 0b100 0b00
SocDK QSPI 0b110 0b00

4.25.1.2. SD card

The Boot ROM searches for a partition of type A2 and loads what it finds there. When barebox is placed in such a partition it will then itself try and mount the second partition of the SD card, which must be of type FAT32. On this partition barebox searches for a file called barebox.bin.

To boot barebox on a Terasic SoCkit, the procedure is as follows (sdb1 is the A2 and sdb2 the FAT32 partition):

mount -t fat /dev/sdb2 /mnt
make socfpga-xload_defconfig
make
make socfpga_defconfig
make

barebox has now generated multiple files in the images directory. So for the SoCkit proceed with:

cat images/barebox-socfpga-sockit-xload.img > /dev/sdb1
cp images/barebox-socfpga-sockit.img /mnt/barebox.bin
umount /mnt

For the EBV Socrates use images/barebox-socfpga-socrates(-xload).img instead.

4.25.1.3. QSPI

The Boot ROM loads the preloader starting from address 0x0 on the QSPI flash. barebox then searches for a barebox image at the 256K offset and loads it.

The default bootsource is SD card, so to change that to QSPI, you have to:

make socfpga-xload_defconfig
make menuconfig

And then select the options MTD and SPI_CADENCE_QUADSPI. Now:

make
cat images/barebox-socfpga-<board>-xload.img > /dev/mtd0

For barebox itself, the build step is like for SD card. The resulting image has to be written to the offset 256K.

Warning! There is a known issue with booting from QSPI and doing Cold/Warm-Resets. Please consult Rocketboards to see how to fix this.

4.25.2. Updating handoff files

(Tools needed: Quartus II + SoCEDS)

As barebox uses some of the autogenerated files from Quartus II, every time Altera makes a new release, there might be some updates to the handoff files. As these files are split up in the code base and generated explicitely for some specific U-boot code base, some manual work might be necessary.

The boardspecific files for arch/arm/boards/<yourboard> are:

  • iocsr_config_cyclone5.c
  • pinmux_config_cyclone5.c -> pinmux_config.c
  • pll_config.h
  • sdram/sdram_config.h -> sdram_config.h
  • sequencer_auto.h
  • sequencer_auto_ac_init.c
  • sequencer_auto_inst_init.c
  • sequencer_defines.h

To update the handoff files, the following procedure is necessary:

  1. Regenerate the project with Qsys
  2. Load up your project in Quartus II and assemble the design
  3. Go to the SoCEDS installation and run ./embedded_command_shell.sh
  4. Now run bsp-editor
  5. Create a new BSP
  6. Select the directory hps_isw_handoff/soc_system_hps_0 under the preloader settings directory
  7. Click Ok than Generate

Now run the command:

scripts/socfpga_import_preloader <SPL_GENERATED_DIR> <ISW_HANDOFF> <BOARD_DIRECTORY>

where <SPL_GENERATED_DIR> is the directory where the bsp-editor generated the files, <ISW_HANDOFF> is the directory where Quartus generated the handoff files, and <BOARD_DIRECTORY> is your board directory under arch/arm/boards.

4.25.3. Integrating new SDRAM driver

This step must only be executed if the SDRAM driver needs updates. It is not necessary for adding a new board to barebox.

The following files are generic and belong into the arch/arm/mach-socfpga directory tree:

  • sdram_io.h
  • sequencer.c as cyclone5-sequencer.c
  • sequencer.h as cyclone5-sequencer.h
  • sequencer_defines.h
  • system.h
  • tclrpt.h

To add these files, run:

scripts/socfpga_get_sequencer <UBOOT-SRC> scripts/socfpga_sequencer_defines_defaults

where <UBOOT-SRC> is the directory where the Altera bsp-editor generated the u-boot directory. Refer to the Altera documentation for how to use the bsp-editor.